Wheelchair Ramp Construction New

Wheelchair Ramp Construction: A wheelchair ramp that has not been constructed properly will usually roll backward when parked and will cause a vehicle accident. This type of wheelchair ramp should have been built on a flat, level surface and at the correct wheelchair ramp slope angle. This article explains how to measure for wheelchair ramp slope angles. I also discuss why wheelchair ramp slope measurement is so important.

Most ramp installation professionals suggest that you build wheelchair ramps at least one inch deep. A wheelchair ramp with a sloping downhill slope should be one and a half inches deep. A wheelchair ramp slope 1:12 that is too steep can cause the wheelchair ramp to flip over or back up onto the pavement. Ideally, you want to use the lowest wheelchair ramp slope that is possible, meaning building the tightest ramp that can accommodate the wheelchair. The maximum wheelchair ramp slope should be one and a half inches deep.

Wheelchair Ramp Construction New

Measuring the wheelchair ramp slope properly is important for several reasons. First, the slope angle can make a difference of as much as twelve inches. Second, the slope angle can affect the time it takes to build the ramp. Third, wheelchair ramp slope angle measurements can affect the cost of the wheelchair ramp.

Most mobility issues begin with poor wheelchair ramp slope or angle measurements. Poor wheelchair ramp slope 2-inch measurements can cause the wheelchair ramp to slip or tilt unexpectedly, causing mobility issues for people using wheelchairs. These issues can also cause wheelchair users to fall when exiting or entering wheelchair vehicles. Building wheelchair ramps correctly can avoid these issues and help avoid wheelchair ramp injuries.

Building wheelchair ramps yourself can be a DIY project. There are several easy wheelchair ramp slope measuring tools you can use. These measuring tools include a tape measure, graph paper, stapler, marking tools like stamps and pencils, and a level. When measuring for wheelchair ramps from the ground, you will need to decide how high your ramp will be. Measure from the ground up, or just below the top of the porch, to the nearest edge.


Measuring wheelchair ramp slope and angles is relatively easy, but measuring for stairs is slightly more difficult. Most stairlifts and access ramps require at least one inch of slope or turn to the right and one inch to the left. It is important to take note that these measurements are in addition to the inside and outside measurements. You must also measure for access angles on both sides of the stairs. Access ramps require an additional quarter-inch of turn.

Access ramps must also be measured for the inside of the ramp. This includes the inside landing size and the inside curve of the ramp. The outside landing size is the largest measurement of the wheelchair ramp; it measures exactly as much as the inside curve. The inside curve is the measurement of the wheelchair ramp’s vertical lift height.

If you choose to have a custom wheelchair ramp made, there are many options when it comes to the measurements. Measuring access ramps requires you to know the wheelchair ramp slope bc, the inside and outside access angles, and the slope distance. You must then cut your ramp according to the specifications you chose. CNC equipment is used to make these cuts, which allows for more precise cuts and saves time and money.

The Americans with Disabilities Act requires that wheelchair ramp risers be at least one inch inside of the tread of the wheelchair. It also requires that the angle of the ramp, which is the distance from the top of the ramp to the bottom, is not less than forty degrees. In order to meet the regulations of the Americans with Disabilities act, wheelchair ramp risers must be a minimum of eighteen inches. To meet the national law, ramps must meet all four corner angle requirements. These are:

Handrails are another important part of wheelchair ramp accessibility. There are different types of handrails, including steel handrails, wood handrails, and metal portable wheelchair ramps. These handrails must not be shorter than eighteen inches, must meet all four corner angle requirements, and must be smooth and rounded. All portable wheelchair ramps, handrails included, must have an external anchor to prevent them from becoming disabled.

One of the most important factors in wheelchair ramp construction is selecting the proper landing size. Landings can range in size from three feet to five feet wide. The landing size will directly impact the wheelchair ramp installation process because if the ramp is too small then the wheelchair will simply roll off the ramp and become disabled. The larger the wheelchair ramp, the more room it has to roll off without hitting the side of the building or other obstacles.

[single_loop]
No comment